audi | Item | Part # | Description / Application | Image | Details |
| Expansion Tank Adaptor: | VZ 41 | Needed for pressurizing the liquid cooling system. "Anodized Aluminum!!"
Applicable: Audi, '96+ Models with female threads on filler neck of expansion tank. |
 |
 |
| Expansion Tank Adaptor: | VZ 31 | Needed for pressurizing the liquid cooling system. "Anodized Aluminum!!"
Applicable: Audi, '97-'90. Models with female threads on filler neck of expansion tank. |
|
|
| Expansion Cap Adaptor: | VZ 30 | Needed for checking blow-off pressure or leakage of expansion tank
cap. "Anodized Aluminum!!" Applicable: Audi, '97-'90. Models with female threads on filler neck of expansion tank. |
|
|
| Expansion Tank Adaptor: | VZ 22 | Needed for pressurizing the liquid cooling system. Comes equipped
with tool# VZ 17, this page, while supplies last. "Anodized Aluminum!!"
Applicable: Audi, '93-'75. Models with male threads on filler neck of expansion. |
|
|
| Expansion Cap Adaptor: | VZ 23 | Needed for checking blow-off pressure or leakage of expansion tank
cap. "Anodized Aluminum!!" Applicable: Audi, '93-'75. Models with male threads on filler neck of expansion. |
|
|
| Expansion Cap Adaptor: | VZ 17 | Needed for checking blow-off pressure or leakage of expansion tank
cap. Used in conjunction with tool# VZ 22, this page. Applicable: Audi, '93-'75. Models with male threads on filler neck of expansion. |
|
|
| Securing Bar: | AU 6018 | Needed for R&R of drive belt sprocket on cam shaft and drive belt
sprocket of intermediate shaft. Applicable: All Audi water-cooled engines, '74+. |
|
|
| Counter Holder: | AU 6016 | Needed for R&R of front crank shaft pulley. Used in conjunction with tool# AU 6017, this page. Applicable: Audi 5 cylinder engines - 80, 90, Quattro, 4000, 5000, Quantum. |
|
|
| Extension Crank Wrench: | AU 6017 | Needed for R&R of front crank shaft bolt. Used in conjunction with tool# AU 6016, this page. Applicable: Audi 5 cylinder engines - 80, 90, Quattro, 4000, 5000, Quantum. Volvo diesel. |
|
|
| Press Driver Kit: | AU 6001 | Needed for the proper installation of the oil seal into steering rack. Applicable: Audi model - 4000, 5000. |
|
|
| Engine Mount Arbor: | AU 6002 | Needed for proper R&R of motor mounts with a 64.5mm O.D. Used in conjunction with a hammer. Applicable: Early model water-cooled Audi. "Knocks them In & Out quick!!" |
|
|
| Engine Mount Arbor: | AU 6003 | Needed for proper R&R of motor mounts with a 74.5mm O.D. Used in conjunction with a hammer. Applicable: Early model water-cooled Audi. "Knocks them In & Out quick!!" |
|
|
| Valve Spring Compressor: | AU 6010 | Needed for R&R of valve spring or rocker arm. Job can be done with
the cylinder head on or off the car. Used in conjunction with tool#
AU 6022. Applicable: Audi 4 & 5 cylinder gasoline powered engines. Porsche model - 924. |
|
|
| Support Bridge: | AU 6022 | Needed for R&R of valve spring or rocker arm. Job can be done with
the cylinder head on or off the car. Used in conjunction with tool#
AU 6010. Applicable: Audi 4 & 5 cylinder gasoline powered engines. Porsche model - 924. |
|
|
| Valve Compressor Armature: | AU 6006 | Needed for R&R of valve spring or rocker arm. Used in conjunction with a C-clamp and/or pneumatic clamp. Applicable: Audi 4 & 5 cylinder gasoline powered engines. Porsche model - 924, 944, 928. |
|
|
| Cylinder Head Alignment Kit: | AU 6000 | Comes equipped with (2) pairs of guide pins, 11X1.75mm and 12X1.75mm. Applicable: Audi model - Scirocco, Rabbit, Dasher, Fox, 4000, 5000. Porsche model - 924. Volvo diesel. |
|
|
| T.D.C. Indicator: | 9710 | Needed for locating T.D.C. on any gasoline powered motor. Simply unscrew a spark plug and twist the rubber hose part of this tool into the spark plug hole. As you rotate the motor with a turning bar, the piston forces air through the whistle part of this tool. Once the whistling stops, the motor is at T.D.C. |
|
|
| Tappet Depressor: | AU 6008 | Needed for preloading cam followers when exchanging valve adjusting
shims. Applicable: Early model 4 cylinder water-cooled gasoline powered engines. |
|
|
| Tappet Depressor: | AU 6009 | Needed for preloading cam followers when exchanging valve adjusting
shims. Applicable: Late model Audi 4 & 5 cylinder gasoline powered engines. Also, Audi & Volvo diesels. |
|
|
| Valve Stem Installer: | AU 6019 | (8mm) Needed for the proper installation of valve stem. Applicable: Audi 4 & 5 cylinder engines. Porsche model - 924. |
|
|
| Valve Stem Seal Pliers: | 10-208 | Needed for the proper extraction of valve stem seals. The inside grooves on the tips of this plier allows for a firm grip of both O.E. and aftermarket seals. |
|
|
| Lock Bolt: | AU 6025 | Needed to secure the crank shaft at T.D.C. during R&R of toothed
timing belt, flywheel/drive plate and crank bolt. Applicable: Audi V-6 engines with 2 valves per cylinder |
|
|
| Lock Pin: | AU 6013 | Crucial for securing Bosch diesel injection pump sprocket from rotating
during R&R of cam shaft drive belt. This Locking Pin also assists
in locating the general timing position of pump. Applicable: All Audi diesel. |
|
|
| Lock Plate: | AU 6014 | Crucial for securing the cam shaft from rotating and maintaining
correct timing position during R&R of cam shaft drive belt. Applicable: All Audi and Volvo diesel engines |
|
|
| Dial Gauge Holder: | AU 6015 | Needed for accurate adjustment of Bosch diesel injection pump. This Dial Gauge Holder screws into the back of the injection pump and comes equipped with a 100mm dial indicator extension pin. Used in conjunction with a dial indicator. |
|
|
| Puller: | AU 6005 | Needed for the proper extraction of diesel injection pump gear of
diesel pump. Applicable: Most every European diesel engine. |
|
|
| O-Ring Spreader: | AU 6020 | Needed to properly install rubber seal ring of CIS fuel injector.
Applicable: All Audi models equipped with with CIS fuel injection. |
|
|
| "C" Clip Spreader: | AU 6007 | Needed for the proper R&R of exhaust manifold spring clip. Applicable: Early model 4 cylinder water-cooled gasoline powered engines. |
|
|
| 22mm Split Socket: | 4491B | Needed for R&R of O2 sensor situated within a confined area. No
need to snip the wires leading to the unit when all you want to do
is check the sensor. 3/8" drive. |
|
|
| Pressure Adaptor: | 1018 | Needed for pressurizing the master cylinder or clutch slave cylinder reservoirs. Used in conjunction with a pressure bleeder. Equipped with a 1/4-18 NPT threaded opening. Applicable: Most every European model. |
|
|
| Radio Hooks: | AU 6026 | (Pair) Needed for the proper removal of radio. Applicable: Audi '98+. |
|
|
| U-Hooks: | 2040 | (Pair) Needed for R&R of radio on all models equipped with a DIN chassis radio mount. |
|
|
| Counter Holder: | AU 6024 | Needed for securing the power steering or water pump pulley from
rotating during R&R of the three bolts that attach the pulley to the
crank shaft. Applicable: 92+; Audi 4 & 5 cylinder gasoline or diesel engines, '75+. |
|
|
| Wire Terminal Extractors: | 9702 | (Large) 4.2mm I.D. and a 5.0mm O.D. Applicable: Most models. |
|
|
| Gear Box Bearing Extractor: | 242 | Needed for the proper extraction of ball bearings from gear boxes. Also for a variety of other applications and models. |
|
|
| 27mm Male Hex Socket: | AU 6011 | Needed for R&R of 27mm female hex timing plug of engine bell housing and R&R of 27mm female hex transmission access cover. 3/8" drive. Applicable: All Audi water-cooled models, '75+. |
|
|
| Pilot Bearing Puller: | 1089 | Designed to extract bearings and bushings with an I.D. of 15mm up
to 20mm. Applicable: Most models. For bearing use only, not bushings: |
|
|
| Front Wheel Bearing R&R Kit: | B 90-VW | Designed to efficiently remove and install the wheel bearing and hub of spindle assemblies. |
|
|
| 22mm Special Tube Socket: | 4491A | 1.) Used for securing the strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side-wall of this socket allows for easy access of an adjusting wrench. 2.) R&R of Oxygen Sensor. "1/2" Drive!!" |
|
|
| Adjuster: | AU 6004 | Needed for proper alignment of camber |
|
|
| Pin Wrench Socket: | AU 6012 | Needed for R&R of grooved ring retaining nut on strut tower of front shock absorber. 1/2" drive. Applicable: Audi 4000. |
|
|
| Front Wheel Bearing R&R Kit: | B 90-AU | Designed to efficiently remove and install the wheel bearing and hub of spindle assemblies. Applicable:Audi models from the early '70's to present with S.R.W.B. and I.F.S., including A.W.D. See pages# 6 & 7, for a detailed applications chart: |
|
|
| Separator: | 1014 | Needed for disassembly of pitman arm type tie rod ends w/o tearing
the ball joint boots. Applicable: Most every Mercedes
model. 25mm |
|
|
designed by AP Logic. copyright 2006 ap logic, gpr parts